操作規程：

Safety operating procedures:

1、提高電焊設備及線路的絕緣性能。使用的電焊設備及電源電纜必須是合格品，其電氣絕緣性能與所使用的電壓等級、周?chē)h(huán)境及運行條件要相適應；焊機應安排專人進行日常維護和保養，防止日曬雨淋，以免焊機電氣絕緣性能降低。

1. Improve the insulation performance of welding equipment and circuits. The welding equipment and power cables used must be qualified products, and their electrical insulation performance must be suitable for the voltage level, surrounding environment, and operating conditions used; Welding machines should be regularly maintained and serviced by dedicated personnel to prevent exposure to sunlight and rain, in order to prevent a decrease in the electrical insulation performance of the welding machine.

2、當焊機發生故障要檢修、移動工作地點、改變接頭或更換保險裝置時，操作前都必須要先切斷電源。

2. When a welding machine malfunctions and needs to be repaired, moved to a new work location, changed joints, or replaced with safety devices, the power supply must be cut off before operation.

3、加強作業人員用電知識及自我防護意識教育，要求焊工作業時必須穿絕緣鞋、戴專用絕緣手套。禁止雨天露天施焊；在特別潮濕的場所焊接，人必須站在干燥的木板或橡膠絕緣片上。

3. Strengthen the education of electrical safety knowledge and self-protection awareness for operators, and require welders to wear insulated shoes and specialized insulated gloves when working. Prohibit welding in the open on rainy days; When welding in particularly humid areas, people must stand on dry wooden boards or rubber insulation sheets.

4、禁止利用金屬結構、管道、軌道和其它金屬連接作導線用。在金屬容器或特別潮濕的場所焊接，行燈電源必須使用12V以下電壓。

4. It is prohibited to use metal structures, pipelines, tracks, and other metal connections as conductors. When welding in metal containers or particularly humid places, the power supply of the portable lamp must use a safe voltage of 12V or less.

5、施工人員在操作時，必須穿戴好各種勞保用品，如工作服、工作帽、手套、腳蓋等工作服不要束在褲腰里，腳蓋應捆在褲腳筒里。

5. Construction personnel must wear various labor protection equipment during operation, such as work clothes, work hats, gloves, foot covers, etc. Work clothes should not be tied around the waist of pants, and foot covers should be tied around the leg of pants.

6、在焊接和切割工作場所，必須有防火設備，如消防栓、滅火器、砂箱以及裝滿水的水桶等。

6. In welding and cutting workplaces, fire prevention equipment must be available, such as fire hydrants, fire extinguishers, sand boxes, and buckets filled with water.

注意事項：

Safety precautions:

1、嚴格按照焊機銘牌上標的數據使用焊機，不得超載使用。

1. Strictly follow the data marked on the welding machine nameplate when using the welding machine, and do not overload it.

2、應在空載狀態下調節電流，焊機工作時，不允許有長時間短路。

2. The current should be adjusted in an unloaded state, and there should be no prolonged short circuit during the operation of the welding machine.

3、使用焊機前，應檢查焊機接線正確、電流范圍符合要求、外殼接地可靠、焊機內無異物后，方可合閘工作。

3. Before using the welding machine, it is necessary to check that the wiring is correct, the current range meets the requirements, the casing is grounded reliably, and there are no foreign objects inside the welding machine before closing it for operation.

4、工作時，焊機鐵心不應有強烈震動，壓緊鐵心的螺絲應擰緊。工作中焊機及電流調節器的溫度不應超過60°C。

4. During operation, the welding machine core should not experience strong vibration, and the screws that press down on the core should be tightened. The temperature of the welding machine and current regulator during work should not exceed 60 ° C.

5、加強維護保養工作，保持焊機內外清潔，保證焊機和焊接軟線絕緣良好，若有破損或燒傷應立即修好。

5. Strengthen maintenance work, keep the inside and outside of the welding machine clean, ensure good insulation between the welding machine and the welding flexible wire. If there is any damage or burn, it should be repaired immediately.

6、定期由電工檢查焊機電路的技術狀況及焊機各處的絕緣性能，如有問題應及時排除。

6. Regularly have electricians inspect the technical condition of the welding machine circuit and the insulation performance of various parts of the welding machine. If there are any problems, they should be promptly eliminated.